[2023] Pass Cisco 350-401 Exam in First Attempt Easily
The Most Efficient 350-401 Pdf Dumps For Assured Success
Cisco 350-401 ENCOR exam comprises of 350-401 exam dumps that include multiple-choice questions, drag-and-drop questions, and simulation questions. The duration of the exam is 120 minutes, and the passing score is 825 out of 1000. 350-401 exam can be taken at any Pearson VUE testing center, and it can also be taken online.
Cisco 350-401 (Implementing Cisco Enterprise Network Core Technologies) Exam is a certification exam designed to test the knowledge and skills of IT professionals who work with Cisco enterprise network technologies. It is a part of the Cisco Certified Network Professional (CCNP) and Cisco Certified Specialist - Enterprise Core certifications. Passing 350-401 exam is a crucial step towards advancing one's career in the field of networking.
NEW QUESTION # 232
In a Cisco SD-Access wireless architecture, which device manages endpoint ID to Edge Node bindings?
- A. fabric edge node.
- B. fabric border node
- C. fabric wireless controller
- D. fabric control plane node
Answer: D
Explanation:
Explanation
SD-Access Wireless Architecture Control Plane Node -A Closer Look
Fabric Control-Plane Node is based on a LISP Map Server / Resolver
Runs the LISP Endpoint ID Database to provide overlay reachability information + A simple Host Database, that tracks Endpoint ID to Edge Node bindings (RLOCs) + Host Database supports multiple types of Endpoint ID (EID), such as IPv4 /32, IPv6 /128* or MAC/48 + Receives prefix registrations from Edge Nodes for wired clients, and from Fabric mode WLCs for wireless clients + Resolves lookup requests from FE to locate Endpoints + Updates Fabric Edge nodes, Border nodes with wireless client mobility and RLOC information Reference: https://www.ciscolive.com/c/dam/r/ciscolive/latam/docs/2018/pdf/BRKEWN-2020.pdf
NEW QUESTION # 233
Refer to the exhibit.
Which command when applied to the Atlanta router reduces type 3 LSA flooding into the backbone area and summarizes the inter-area routes on the Dallas router?
- A. Atlanta(config-route)#area 1 range 192.168.0.0 255.255.252.0
- B. Atlanta(config-route)#area 1 range 192.168.0.0 255.255.248.0
- C. Atlanta(config-route)#area 0 range 192.168.0.0 255.255.248.0
- D. Atlanta(config-route)#area 0 range 192.168.0.0 255.255.252.0
Answer: A
NEW QUESTION # 234 
Refer to the exhibit. Which configuration is required to summarize the Area 2 networks that are advertised to Area 0?
- A. Option D
- B. Option A
- C. Option B
- D. Option C
Answer: D
NEW QUESTION # 235
During deployment, a network engineer notices that voice traffic is not being tagged correctly as it traverses the network. Which COS to DSCP map must be modified to ensure that voice traffic is treated properly?
- A. COS of 5 to DSCP 46
- B. COS of 7 to DSCP 48
- C. COS of 3 to DSCP of 26
- D. COS of 6 to DSCP 46
Answer: A
NEW QUESTION # 236
Refer to the exhibit.
What are two effect of this configuration? (Choose two.)
- A. The 10.1.1.0/27 subnet is assigned as the inside local addresses.
- B. The 10.1.1.0/27 subnet is assigned as the inside global address range.
- C. Inside source addresses are translated to the 209.165.201.0/27 subnet.
- D. The 209.165.201.0/27 subnet is assigned as the outside local address range.
- E. It establishes a one-to-one NAT translation.
Answer: A,C
NEW QUESTION # 237
Refer to the exhibit.
An engineer must allow all users in the 10.2.2.0/24 subnet to access the Internet. To conserve address space the public Interface address of 209 165 201.1 must be used for all external communication. Which command set accomplishes these requirements?
A)
B)
C)
D)
- A. Option D
- B. Option A
- C. Option B
- D. Option C
Answer: D
NEW QUESTION # 238
What are two methods of ensuring that the multicast RPF check passes without changing the unicast routing table? (Choose two.)
- A. implementing static mroutes
- B. disabling the interface of the router back to the multicast source
- C. implementing OSPF routing protocol
- D. implementing MBGP
- E. disabling BGP routing protocol
Answer: A,D
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/ip-multicast/16450-mcastguide0.html
NEW QUESTION # 239 
Refer to the exhibit Drag and drop the snippets into the RESTCONF request to form the request that returns this response Not all options are used
Answer:
Explanation:
NEW QUESTION # 240
Refer to the exhibit.
An engineer must allow R1 to advertise the 192 168.1 0/24 network to R2 R1 must perform this action without sending OSPF packets to SW1 Which command set should be applied?
A)
B)
C)
D)
- A. Option C
- B. Option D
- C. Option B
- D. Option A
Answer: C
NEW QUESTION # 241
Which access point mode allows a supported AP to function like a WLAN client would, associating and identifying client connectivity issues?
- A. sniffer mode
- B. client mode
- C. sensor mode
- D. SE-connect mode
Answer: C
Explanation:
Explanation
As these wireless networks grow especially in remote facilities where IT professionals may not always be onsite, it becomes even more important to be able to quickly identify and resolve potential connectivity issuesideally before the users complain or notice connectivity degradation. To address these issues we have created Cisco's Wireless Service Assurance and a new AP mode called "sensor"mode. Cisco's Wireless Service Assurance platform has three components, namely, Wireless PerformanceAnalytics, Real-time Client Troubleshooting, and Proactive Health Assessment. Using a supported AP ordedicated sensor the device can actually function much like a WLAN client would associating andidentifying client connectivity issues within the network in real time without requiring an IT or technician to beon site.
Reference:
https://content.cisco.com/chapter.sjs?uri=/searchable/chapter/content/dam/en/us/td/docs/wireless/controller/techn
NEW QUESTION # 242
Refer to the exhibit.
Which statement about the OPSF debug output is true?
- A. The output displays OSPF messages which router R1 has sent or received on interface Fa0/1.
- B. The output displays OSPF messages which router R1 has sent or received on all interfaces.
- C. The output displays OSPF hello messages which router R1 has sent or received on interface Fa0/1.
- D. The output displays OSPF hello and LSACK messages which router R1 has sent or received.
Answer: C
NEW QUESTION # 243 
Refer to the exhibit. An engineer must deny HTTP traffic from host A to host B while allowing all other communication between the hosts, drag and drop the commands into the configuration to achieve these results. Some commands may be used more than once. Not all commands are used.
Answer:
Explanation:
NEW QUESTION # 244
Refer to the exhibit.
What does the output confirm about the switch's spanning tree configuration?
- A. The spanning-tree operation mode for this switch is IEEE.
- B. The spanning-tree operation mode for this switch is PVST+.
- C. The spanning-tree mode stp ieee command was entered on this switch
- D. The spanning-tree operation mode for this switch is PVST
Answer: B
NEW QUESTION # 245
Which are two interface requirements for turbo flooding? (Choose two.)
- A. The interface is configured for GRE encapsulation.
- B. The interface is configured for 802.1Q encapsulation.
- C. The interface is Ethernet.
- D. The interface is configured for ARPA encapsulation.
- E. The interface is PPP.
Answer: C,D
NEW QUESTION # 246
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
- A. security group tag number assigned to each port on a network
- B. security group tag number assigned to each user on a switch
- C. security group tag ACL assigned to each router on a network
- D. security group tag ACL assigned to each port on a switch
Answer: A
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag (SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
NEW QUESTION # 247
Refer to the exhibit.
Refer to the exhibit. What are two results of the NAT configuration? (Choose two.)
- A. R1 processes packets entering E0/0 and S0/0 by examining the source IP address.
- B. A packet that is sent to 200.1.1.1 from 10.1.1.1 is translated to 209.165.201.1 on R1.
- C. Packets with a destination of 200.1.1.1 are translated to 10.1.1.1 or .2. respectively.
- D. R1 looks at the destination IP address of packets entering S0/0 and destined for inside hosts.
- E. R1 is performing NAT for inside addresses and outside address.
Answer: B,D
NEW QUESTION # 248
Refer to the exhibit.
An engineer must configure an ERSPAN session with the remote end of the session 10.10.0.1. Which commands must be added to complete the configuration?
- A.
- B.
- C.
- D.
Answer: A
Explanation:
Example: Configuring an ERSPAN Source Session on a WAN Interface
The following example shows how to configure more than one WAN interface in a single ERSPAN source monitor session. Multiple interfaces have been separated by a commas.
monitor session 100 type erspan-source
source interface Serial 0/1/0:0, Serial 0/1/0:6
Example: Configuring an ERSPAN Destination Session
The following example shows how to configure an ERSPAN destination session:
monitor session 2 type erspan-destination
destination interface GigabitEthernet1/3/2
destination interface GigabitEthernet2/2/0
source
erspan-id 100
ip address 10.10.0.1
NEW QUESTION # 249
Which protocol infers that a YANG data model is being used?
- A. REST
- B. RESTCONF
- C. NX-API
- D. SNMP
Answer: B
Explanation:
YANG (Yet another Next Generation) is a data modeling language for the definition of data sent over network management protocols such as the NETCONF and RESTCONF.
NEW QUESTION # 250
z
Refer to the exhibit. Which configuration must be applied to R to enable R to reach the server at 172.16.0.1?
A)
B)
C)
D)
- A. Option C
- B. Option D
- C. Option A
- D. Option B
Answer: B
NEW QUESTION # 251
Which DHCP option provides the CAPWAP APs with the address of the wireless controller(s)?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
Explanation:
NEW QUESTION # 252
Refer to the exhibit.
Which configuration establishes EBGP neighborship between these two directly connected neighbors and exchanges the loopback network of the two routers through BGP?
A)
B)
C)
D)
- A. Option C
- B. Option A
- C. Option D
- D. Option B
Answer: B
Explanation:
Explanation
With BGP, we must advertise the correct network and subnet mask in the "network" command (in this case network 10.1.1.0/24 on R1 and network 10.2.2.0/24 on R2). BGP is very strict in the routing advertisements. In other words, BGP only advertises the network which exists exactly in the routing table. In this case, if you put the command "network x.x.0.0 mask 255.255.0.0" or
"network x.0.0.0 mask 255.0.0.0" or "network x.x.x.x mask 255.255.255.255" then BGP will not advertise anything.
It is easy to establish eBGP neighborship via the direct link. But let's see what are required when we want to establish eBGP neighborship via their loopback interfaces. We will need two commands:
+ the command "neighbor 10.1.1.1 ebgp-multihop 2" on R1 and "neighbor 10.2.2.2 ebgpmultihop
2" on R1. This command increases the TTL value to 2 so that BGP updates can reach the BGP neighbor which is two hops away.
+ Answer 'R1 (config) #router bgp 1
R1 (config-router) #neighbor 192.168.10.2 remote-as 2
R1 (config-router) #network 10.1.1.0 mask 255.255.255.0
R2 (config) #router bgp 2
R2 (config-router) #neighbor 192.168.10.1 remote-as 1
R2 (config-router) #network 10.2.2.0 mask 255.255.255.0
Quick Wireless Summary
Cisco Access Points (APs) can operate in one of two modes: autonomous or lightweight
+ Autonomous: self-sufficient and standalone. Used for small wireless networks.
+ Lightweight: A Cisco lightweight AP (LAP) has to join a Wireless LAN Controller (WLC) to function.
LAP and WLC communicate with each other via a logical pair of CAPWAP tunnels.
- Control and Provisioning for Wireless Access Point (CAPWAP) is an IETF standard for control messaging for setup, authentication and operations between APs and WLCs. CAPWAP is similar to LWAPP except the following differences:
+CAPWAP uses Datagram Transport Layer Security (DTLS) for authentication and encryption to protect traffic between APs and controllers. LWAPP uses AES.
+ CAPWAP has a dynamic maximum transmission unit (MTU) discovery mechanism.
+ CAPWAP runs on UDP ports 5246 (control messages) and 5247 (data messages) An LAP operates in one of six different modes:
+ Local mode (default mode): measures noise floor and interference, and scans for intrusion detection (IDS) events every 180 seconds on unused channels
+ FlexConnect, formerly known as Hybrid Remote Edge AP (H-REAP), mode: allows data traffic to be switched locally and not go back to the controller. The FlexConnect AP can perform standalone client authentication and switch VLAN traffic locally even when it's disconnected to the WLC (Local Switched). FlexConnect AP can also tunnel (via CAPWAP) both user wireless data and control traffic to a centralized WLC (Central Switched).
+ Monitor mode: does not handle data traffic between clients and the infrastructure. It acts like a sensor for location-based services (LBS), rogue AP detection, and IDS
+ Rogue detector mode: monitor for rogue APs. It does not handle data at all.
+ Sniffer mode: run as a sniffer and captures and forwards all the packets on a particular channel to a remote machine where you can use protocol analysis tool (Wireshark, Airopeek, etc) to review the packets and diagnose issues. Strictly used for troubleshooting purposes.
+ Bridge mode: bridge together the WLAN and the wired infrastructure together.
Mobility Express is the ability to use an access point (AP) as a controller instead of a real WLAN controller. But this solution is only suitable for small to midsize, or multi-site branch locations where you might not want to invest in a dedicated WLC. A Mobility Express WLC can support up to 100 Aps
NEW QUESTION # 253
Refer to the exhibit.
Assuming that R is a CE router, which VRF is assigned to Gi0/0 on R1?
- A. Default VRF
- B. Management VRF
- C. VRF VPN_B
- D. VRF VPN_A
Answer: A
Explanation:
Explanation
There is nothing special with the configuration of Gi0/0 on R1. Only Gi0/0 interface on R2 is assigned to VRF VPN_A. The default VRF here is similar to the global routing table concept in Cisco IOS
NEW QUESTION # 254
......
Key Exam Details
The Cisco 350-401 ENCOR has a duration of 120 minutes and can be scheduled through Pearson VUE in the English and Japanese languages. Following the recent certification updates, learners will be required to pass 350-401 exam together with a concentration test of their liking to qualify for the CCNP Enterprise certificate.
We offers you the latest free online 350-401 dumps to practice: https://www.vceengine.com/350-401-vce-test-engine.html
Cisco 350-401 Real Exam Questions Guaranteed Updated Dump: https://drive.google.com/open?id=13U9EDirEGNfbwGDrfrphPw_qoSaicn8f
